Worth AnchorMate Anchor Reel Anchor Control System
Located in Steven Point, Wisconsin, the Worth Company is proud to be a family owned and operated manufacturer in the USA.
The Worth Company has been the number one source of fishing lure components and Key Rings for manufacturers for over 70 years. Major automotive and tackle manufacturers throughout the world look to us for quality materials and equipment because the Worth name stands for workmanship and value. Four generations of the Worth family have spent over 70 years perfecting our manufacturing processes, producing our own exacting tooling standards, identifying the finest materials and developing the most durable finishes.
Our state-of-the-art manufacturing facility in Stevens Point, Wisconsin is the industry's largest and most sophisticated. With complete in-house production facilities, we are able to perform all facets of the manufacturing process.
The end result of this technological superiority is that we can do more things, faster and in greater quantities, meaning greater cost savings to you.
By maintaining our high-volume, in-house operation we are better able to answer your needs. Our location and large inventory give us the ability to process and deliver your orders faster and with better service than our competitors.
Together, our experience, industry commitment, high-volume production capacity, cost-efficiency and service all add up to the quality you get in every product from Worth.
How to install the Anchormate®
STEP 1: Place Bow Mount on corner of boat, mark and drill 4 holes to match base of mount. On boats with a deck, or no opening in bow plate, drill a 3/4" hole directly beneath rear Bow Mount pulley for anchor line to pass through. Attach Bow Mount with 1/4" bolts. Self tapping sheet metal screws or wood screws may be used depending on boat's construction.
STEP 2: Place Anchor Reel on either side of boat near oar locks or transom as desired. IMPORTANT! Be sure to leave clearance so that the reel will not interfere with the operation of oars or motor.
STEP 3:Mark and drill three holes to match reel mounting brackets. Attach with ¼" bolts placing the 6 nylon washers on each side of hull to make installation watertight.
Although line guides are not necessary, we recommend their use to keep anchor line along the side of the boat and out of the way. The guides are not furnished but are available at most marine dealers. Use as few as possible to keep line drag at a minimum.
STEP 5: Install the pulley - We recommend the use of a swivel pulley on boats which have a deck or bow plate. To install thread anchor line from reel, through line guides and the unmounted swivel pulley (not furnished), then up through deck or bow plate, and over pulleys in bow mount as shown.
STEP 6 :Attach anchor, or weight, to take up line slack and cause tension on the line. Grasp swivel pulley (a tiller pulley is ideal) and position inside of bow directly beneath rear bow mount pulley. Mark holes and attach pulley. Be certain that the swivel pulley does not rub on deck or bow plate and that anchor line does not rub on edge of hole in deck.
Due to the variety of materials and design used in the construction of boats (wood, metal, fiberglass, etc.) we have NOT included mounting hardware such as bolts, screws, line guides or pulleys. These must be purchased to meet your individual requirements.
YOU WILL REQUIRE THE FOLLOWING:
3 bolts or screws to fasten the Anchormate reel - 4 bolts or screws to fasten the bow mount
THE FOLLOWING ARE RECOMMENDED:
1 swivel pulley at the bow 2 line guides along the side of the boatYou should be able to purchase the above items at nominal cost from the dealer where you purchased your Anchormate.
REEL OPERATION INSTRUCTIONS
The ANCHORMATE® is the ultimate in operating ease. To release the anchor, simply turn the control button in a clockwise direction. The anchor will drop until you release the button or the anchor hits bottom,To raise the anchor or, urn the handle clockwise. DO NOT TURN BUTTON OR HANDLE COUNTER CLOCKWISE DAMAGE MAY RESULT.
The reel is factory lubricated with waterproof grease, however, periodic lubrication is required. To do this, follow the disassembly instructions. The frequency of this procedure will depend on the amount of exposure to the elements. The reel and bow fixture should be covered if possible when stored outside, and should be flushed with fresh water after each use in saltwater.