How to Apply Interlux Prop & Drive Application Data
The information provided here has been reproduced courtesy of Interlux Paint Company. Wholesale Marine reproduced this information 2/08/2008.
PRODUCT DESCRIPTION
Trilux Prop & Drive Aerosol antifouling paint is formulated specifically for aluminium outboards, outdrives and aluminium hulls in underwater areas. When applied over properly primed metal, Trilux Prop & Drive Aerosol will provide good antifouling protection. Biolux Technology is used to control slime growth. Trilux Prop & Drive Aerosol is for use in fresh, salt and brackish water.
PRODUCT INFORMATION
Colour Y5493A-Black, Y5495A-Gray, Y5498A-White, Y5499A-Clear
Finish Matte
Typical Shelf Life 2 yrs
Unit Size 16 fl.oz
DRYING/OVERCOATING INFORMATION
Drying
41F 50F 73F 95F
Touch Dry [ISO] 45mins 30mins 30mins 30mins
Immersion 24hrs 16hrs 12hrs 8hrs
Overcoating
Substrate Temperature
41F 50F 73F 95F
Overcoated By Min Max Min Max Min Max Min Max
Trilux Prop & Drive Aerosol nbsp16hrs nbsp- nbsp12hrs nbsp- nbsp6hrs nbsp- nbsp4hrs nbsp-
APPLICATION AND USE
BARE ALUMINUM:
For Black, White and Gray - Sand with medium grade (grit) emery cloth to a bright metal finish. Immediately apply Viny-Lux Primewash 353/354 thinned 25% with Viny-Lux Solvent 355. Allow to dry for 1-24 hours. Apply 1 full can of Primocon Aerosol Primer YPA985 in a multi-layer procedure.
For Clear - Sand with medium grade (grit) emery cloth. Prime and reapply factory finish before applying Trilux Prop & Drive Aerosol.
PREVIOUSLY PAINTED SURFACES:
with Trilux Prop & Drive Aerosol: Sand with 80 grade (grit) paper.
with Factory Finish or Antifouling Paint: Sand with 80 grade (grit) paper. Clean with Special Thinner 216. Resand any areas where bare aluminium is exposed with medium grade (grit) emery cloth and wipe clean. Follow procedure for bare aluminium above.
Method
At least 2 coats should be applied. Hold can 12-16 inches from the unit when applying the paint. Wait for minimum overcoating time between coats. Continue until the entire can has been used per outdrive. Be sure the paint is completely dry before immersion and allow minimum immersion time.
Hints
Mixing Shake can well, listen for mixing ball & continue shaking vigourously for at least 2 minutes. It is best to shake in an up and down motion. IF CAN IS NOT SHAKEN PROPERLY CLOGGING OF THE TIP MAY RESULT. Trilux Prop & Drive Aerosol Clear is recommended for light colored outdrives such as Volvo, Yamaha and Evinrude. It may appear hazy over Mercury (black) or any dark colored outdrives. For Mercury outdrives use Trilux Prop & Drive Aerosol Black 5493A.
Other
Put extra coats of Trilux Prop & Drive Aerosol on the props and other running gear. For best antifouling protection use entire can of primer and Trilux Prop & Drive Aerosol for each lower unit.
Some Important Points Product temperature should be minimum 10C/50F and maximum 29C/85F. Ambient temperature should be minimum 10C/50F and maximum 35C/95F. Substrate temperature should be minimum 10C/50F and maximum 29C/85F.
Compatibility/Substrates
Apply to clean, dry, properly prepared surfaces only. Do not apply to tin-based paint such as Micron 33, 44 or Tri-Lux IIT. Must be sealed with Primocon Aerosol YPA985.
Number of Coats 2
Use an entire can of Trilux Prop & Drive Aerosol per lower unit.
Coverage (Theoretical) - 122.1 (ft/Gal) 1 aerosol can will cover 1 lower unit (2 coats)
Recommended DFT 2.0 mils dry
Application Methods Aerosol can
TRANSPORTATION,STORAGE AND SAFETY INFORMATION
TRANSPORTATION:
Trilux Prop & Drive Aerosol should be kept in securely closed containers during transport and storage.
STORAGE:
Exposure to air and extremes of temperature should be avoided. For the full shelf life of Trilux Prop & Drive Aerosol to be realised ensure that between use the container is firmly closed and the temperature is between 5C/40F and 35C/95F. Keep out of direct sunlight.
Safety DISPOSAL: Container Disposal: Triple Rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill or by other procedures approved by state or local authorities. Pesticide Disposal: Open dumping is prohibited. Pesticide, spray mixture or rinsate that cannot be used or chemically reprocessed should be disposed of according to procedures approved by Federal, state, or local disposal authorities. GENERAL: Read the label safety section for Health and Safety Information, also available from our Technical Help Line.
Contains biocides. Antifoulings should only be wet sanded. Never dry sand or burn-off old antifoulings.
IMPORTANT NOTES
The performance of any marine paint or coating depends on many factors outside the control of International Paint LLC., including surface preparation, proper application, and environmental conditions. Therefore, International Paint LLC. cannot guarantee this product’s suitability for your particular purpose or application. IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND/OR MERCHANTABILITY ARE EXCEEDED. International Paint Inc. SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. By purchase of this product, the buyer agrees that the sole exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at International Paint LLC. option.
Interlux, the Akzo Nobel logo and other products mentioned in this publication are trademarks of, or licensed to Akzo Nobel.