Welcome to WholesaleMarine.com

CALL TOLL-FREE
M-F 9:00 AM - 6:00 PM EST
1-877-388-2628
My Cart (0)

Free Shipping Promo

Interlux Nautical Super Pro Guard Antifouling

SKU # ILX-NAU770-1.1

Be the first to review this product

Availability: In Stock - Ships Today
Shipping Restrictions: Ground Only To Contiguous 48 States
X
X

* Required Fields

$218.41

Our Price $126.68

* Required Fields

SKU# ILX-NAU770-1.1

Description

Super ProGuard is performance, value and reliability all in one. Super ProGuard is a hard modified epoxy, low V.O.C., high copper antifouling paint formulated to effectively provided year round protection in warm waters or where fouling is at its worst. Super ProGuard can be applied directly over most properly prepared antifouling paints. Recommended for use on the underwater areas of fiberglass, wood, and properly primed metal (except aluminum) boat hulls and can be used in fresh, salt and brackish waters.

  • Hard modified epoxy
  • Long lasting year round performance
  • High copper, for excellent performance in high fouling waters
  • Compatible over most antifouling paints
  • Low V.O.C.

Sold in Gallons

Available in:  Black (ILX-NAU773-1)

                        Blue (ILX-NAU770-1)

                       Red (ILX-NAU772-1)

Specifications
Manufacturer Interlux Paint
Number of Seasons Single Season
Hull Material Fiberglass, Steel, Wood
How to Apply

APPLICATION DATA METHOD: Airless Spray, Brush, Conventional Spray, Roller

NUMBER OF COATS: 2, 3 on bare wood

DRY FILM THICKNESS PER COAT: 2 mils (3.5 mils wet)

COVERAGE: 470 sq. ft/gal.

APPLICATION TEMP: 50°F Min. / 95°F Max.

THINNER: Special Thinner 216

DRY TIMES:
Temp To Touch To Recoat To Launch
95°F 30 MIN 1 HR 6 HR
73°F 1 HR 2 HR 8 HR
50°F 2 HR 6 HR 12 HR

PREVIOUSLY PAINTED SURFACES - GOOD CONDITION: Remove all traces of loose paint by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene¹ using the two-rag method before and after sanding. Apply two coats of Super ProGuard allowing for appropriate dry times.

PREVIOUSLY PAINTED SURFACE - POOR CONDITION: Completely remove old antifouling
paint, after all old antifouling paint has been completely removed, sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene¹ using  the two-rag method before and after sanding. Apply two coats of Super Proguard allowing for appropriate dry times.

BARE FIBERGLASS: Scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry.  Remove mold release wax and surface contamination by wiping down the surface with Xylene¹ using the two-rag method. Fill any surface imperfections with approved filler for underwater use. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with  Xylene¹ using the two-rag method. Apply two coats of Super ProGuard allowing for appropriate dry times.

 

BARE WOOD: Sand the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene¹ using the two-rag method before and after sanding. Apply the first coat of Super Proguard thinned 10% with Xylene². Apply two finish coats of Super Proguard allowing for appropriate dry times.

UNDERWATER METALS: Apply an approved underwater metal primer as per manufacturer’s instructions. Apply two coats of Super Proguard allowing for appropriate dry times. Do not use on aluminum.

APPLICATION METHODS: 

Mixing: Stir well before use.
Cleaner: Acetone or Xylene¹
Thinning: Thin 10% with Xylene². Do not exceed 10% by volume.
Ventilation and Humidity Control: Apply in dry, well ventilated conditions.
Roller: Use a 3/8" nap solvent resistant roller.
Airless Spray: Tip Size: 0.53-0.66 mm/21-26 thou. Pressure: 170-204 bar/2500-3000 psi.
Conventional Spray: Pressure Pot: Tip Size: 1.8-2.2 mm/70-85 thou. Pressure: 4.08-4.76bar/60-70psi (gun pressure); 10-15 psi (pot pressure).
Related Products

More Views