Interlux Sikkens Cetol Wood Finish
Cetol Marine with Next Wave UV-absorbing technology is a durable translucent protective wood finish for use above the waterline on interior and exterior woods. Next Wave technology is the next generation of Cetol Marine from Sikkens with a unique UV-absorbing package which is specialty resins and advanced UV absorbers that provide greater protection, durability and longevity. Cetoll Marine provides a flexible breathable finish along with weather protection for teak and other hard woods all with ease of application and mainenance. It is formulated with Next Wave technology, special alkyd resin and high quality synthetic UV-absorbing pigments which shields wood against damaging UV rays and produces an attractive dark amber appearance on wood.
|Manufacture Part Number||IVA-300Q|
Write Your Own Review
How To Apply
APPLICATION DATA METHOD: Brush
NUMBER OF COATS: 2-3
COVERAGE: 400 sq. ft/gal.
APPLICATION TEMP: 50°F Min. / 95°F Max.
THINNER: Do Not Thin
|Temp||To Touch||To Hard Dry||To Recoat|
|73°F||4 HR||24 HR||24 HR|
NEW WOOD: Wipe the wood with Interlux® Special Thinner 216 to remove any natural surface oils and contaminants. Allow to dry, sand surfaces with 180-220 (grade) grit paper (always sand along the length of the grain). Remove all sanding residue by vacuuming the surface. Wipe the surface with Interlux Special Thinner 216 and allow to dry completely prior to application of Cetol® Marine. When working in interior or confined spaces always ensure there is proper ventilation. If the wood is exposed for more than 24 hours, clean the surface again with Interlux Special Thinner 216 in order to remove any contaminants.
PREVIOUSLY COATED WOOD: Remove all coatings prior to application of Cetol® Marine. To remove old coating, either sand with 120-180 (grade) grit paper or use Interlux Interstrip 299E chemical stripper which has been designed for marine use. Once previous coating has been removed, follow instructions for New Exterior/Interior wood.
WEATHERED/OILED WOOD: Remove all coatings prior to application of Cetol® Marine. To remove old coating, either sand with 120-180 (grade) grit paper or use Interlux Interstrip 299E chemical stripper which has been designed for marine use. Once previous coating has been removed, follow instructions for New Exterior/Interior wood.
APPLICATION INFORMATION: The wood moisture content should be below 18%. Apply liberally using a long-haired bristle brush, smoothly, in the direction of the grain. Keep a wet edge to prevent lap marks and thoroughly saturate end grains where possible. Apply 3 coats of Cetol® Marine. Always allow 24 hours drying time in between coats. Sanding between coats is not recommended as this will result in a reduction of dry film thickness. Recommended film thickness must be applied to ensure effective product performance. Make regular inspections to all coated areas. Problem areas should be attended to immediately and maintenance coats should be routinely applied. If the coating is allowed to weather beyond the regular maintenance period of 1 year, returning this surface to excellent condition will be more difficult. Before application of a maintenance coat of Cetol® Marine, clean the surface with Interlux® All Purpose Boat Soap to remove any surface contaminants as per instructions on label. If blue fungi or mildew are present then they can be treated with Interlux Premium Teak Restorer with a nylon scruffing pad as per instructions on label. Rinse with fresh water and allow to dry. Sand lightly with 220-320 (grade) grit paper. After sanding, wipe with Interlux Special Thinner 216 and let to dry thoroughly prior to the application of the maintenance coat of Cetol® Marine. If using as a deck paint, sprinkle Interlux Intergrip (non-skid compound) onto the wet surface of the second coat of Cetol® Marine. Allow to dry for 24 hours. Remove excess Intergrip using a vacuum. Maintenance requirements may be increased when Intergrip is used. If high gloss finish is required, use Cetol® Marine Gloss following the initial application of Cetol® Marine. Refer to Cetol® Marine Gloss datasheet for further details. Cetol® Marine Gloss is NOT suitable for use on decks. Before applying any Cetol® products, prepare a 3 coat test sample on your wood to confirm desired color results. To achieve optimal color results always use the same Cetol® product initially applied when overcoating or applying maintenance coats. If Cetol® Marine is spilled on gelcoat, remove immediately. Difficult stains may be removed from gelcoat with Interlux Fiberglass Solvent Wash 202. Do not allow excess Fiberglass Solvent Wash 202 to remain on gelcoat. For painted surfaces ONLY use Interlux Special Thinner 216. Do not allow excess Special Thinner 216 to remain on painted surfaces. Do not apply at temperatures within 3°C of dew point or in wet weather. Substrate temperature should be minimum 10°C/50°F and maximum 35°C/95°F. Ambient tem perature should be minimum 10° C/50°F and maximum 35°C/95°F. Product temperature sh ould be no less than 10°C/50°F and maximum 35°C/95°F. Avoid painting in direct sunlight . Suitable for use on all types of wood including oily timbers such as Teak.