|SKU||Container Size||Paint Color||Retail Price||Our Price||Savings|
|ILX-3449G||Gallon||Red||$338.98||$198.87||You Save 41%|
|ILX-3559G||Gallon||Green||$338.98||$198.87||You Save 41%|
|ILX-3669G||Gallon||Blue||$338.98||$196.61||You Save 42%|
|ILX-3779G||Gallon||Black||$338.98||$196.61||You Save 42%|
Interlux Ultra with Biolux Antifouling Boat Bottom Paint
Ultra with Biolux is a high strength antifouling paint with a high load of cuprous oxide. Ultra uses Biolux technology to block slime and improve antifouling performance. New fast dry formula allows Ultra to be painted and launched the same day. Interlux part numbers 3449 Red, 3559 Green, 3669 Blue, 3779 Black.
- Ultra strong formula for high fouling areas
- Fast dry-paint and launch same day
- Biolux increases antifouling performance
- Use wherever the fouling challange is severe
|Manufacture Part Number||3449Q.1|
|Number of Seasons||Multi Season|
|Hull Material||Fiberglass, Steel, Wood|
|Is Boat Trailerable||Trailerable|
Write Your Own Review
How To Apply
APPLICATION DATA METHOD: Brush, roller, airless or conventional spray.
NUMBER OF COATS: 2 minimum.
DRY FILM THICKNESS PER COAT: 2 mils (3.3 wet mils)
COVERAGE: 455 sq. ft/gal.
APPLICATION TEMP: 50° F. Min. / 90°F. Max.
THINNER: Brush Ease 433 - No more than 10% by volume
|Temp||To Touch||To Recoat||To Launch|
|90F||1/2 HR||1 HR||6 HR|
|70F||1 HR||2 HR||8 HR|
|50F||2 HR||6 HR||12 HR|
MAXIMUM IMMERSION TIME: 60 Days
PREVIOUSLY PAINTED SURFACES: In Good Condition Remove loose paint by sanding with 80 grade (grit) paper, wipe with Special Thinner 216. In Poor Condition Remove antifouling paint in poor condition with Interstrip Semi-Paste 299E.
BARE FIBERGLASS: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water and allow to dry. Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202. While the surface is still wet, wipe with a clean, dry rag. Continue this process until the entire surface has been cleaned. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with Fiberglass Solvent Wash 202. Alternative degreasing methods include the use of 202V Low VOC degreaser or YMA601 Fiberglass Surface Prep. For complete details see the Interprotect Bulletin - The Ultimate No Sand System. Once the hull is contaminent-free and dry, apply the first coat of primer.
BARE WOOD: Sand with 80 grade (grit) paper. Remove sanding residue. Apply first coat reduced 10% with Special Thinner 216. If primer is preferred use Primocon YPA984. Fill seams, if necessary, with Seam Compound Brown 30.
STEEL HULLS: Prime with Interprotect 2000E to achieve 10 mils total dry film thickness. See the Interprotect 2000E Technical Datasheet for surface preparation and application guidelines.
UNDERWATER METAL PARTS: See Interlux bulletin
DO NOT USE THIS PRODUCT ON ALUMINUM HULLS AND OUTDRIVES.
APPLICATION INFORMATION: Color will change on immersion, this will not affect antifouling performance. Colors may fade or change color at the waterline. Apply to clean, dry, properly prepared surfaces only. Ultra with Biolux can be applied to most popular antifouling paints as long as the old coating has been aged, is tightly adhered and is in sound condition. Do not apply over tin-based copolymer antifouling paints. Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.53 mm/21 thou. Conventional Spray Pressure Pot: Pressure: 4.08-4.76 bar/60-70 psi (gun pressure); 10-15 psi (pot pressure). Tip Size: 1.8-2.2 mm/70-85 thou. Roller Use a 3/8" nap solvent resistant roller.