Welcome to WholesaleMarine.com

CALL TOLL-FREE
M-F 9:00 AM - 6:00 PM EST
1-877-388-2628
My Cart (0)

Free Shipping Promo

Pettit Horizons Ablative Antifouling Bottom Marine Paint

SKU # PET-1250G.1

Be the first to review this product

Availability: In Stock - Ships Today
Shipping Restrictions: Ground Only To Contiguous 48 States
Size Calculation
X Size Calculation
Color Chart
X Color Chart

* Required Fields

Starting At:

$282.46

Our Price $158.40

* Required Fields

SKU# PET-1250G.1

More Views

  • Color Chart
  • Size Calculation
Description
SKUContainer SizePaint ColorRetail PriceOur PriceSavings 
PET-1250GGallonBlue$282.46$158.40You Save 44%
PET-1850GGallonBlack$282.46$161.33You Save 43%

Pettit Horizons Ablative Bottom Paint

Horizons Ablative Antifouling Bottom Paint offers excellent protection from fouling along with all of the benefits of ablative antifouling. Economically priced, Horizons performs well in all conditions including severe fouling waters. This product is the standard ablative antifouling for many boatyards. Use 185 Ablative Thinner.

***ONLY AVAILABLE FOR SHIPPING WITHIN CONTINENTAL 48 STATES***

  • Ablative Technology Reduces Coating Build-up
  • Launch and Relaunch without Repainting
  • Economically Priced Multi-season Protection
  • Excellent for Trailered Boats
  • Similar Performance to Micron CSC at a Lower Price

 

 

Specifications
Manufacturer Pettit Paint
Manufacture Part Number 1250G.1
Number of Seasons Multi Season
Hull Material Fiberglass, Steel, Wood
Is Boat Trailerable Trailerable
How To Apply

APPLICATION DATA METHOD: Brush, Roller, Airless or Conventional Spray.

NUMBER OF COATS: 2 or 3

DRY FILM THICKNESS PER COAT: 2 mils (3.2 wet mils)

COVERAGE: 500 sq. ft/gal.

APPLICATION TEMP: 50°F Min. / 90°F Max.

THINNER: 120 Brushing Thinner

DRY TIMES:
Temp To Recoat To Launch
90°F 3 HR 8 HR
70°F 6 HR 16 HR
50°F 12 HR 48 HR

*The above dry times are minimums. Horizons may be recoated after the minimum time shown. There is no maximum dry time before launching.

PREVIOUSLY PAINTED SURFACES: If the previous coating is in good condition, thoroughly sand with 80 grit paper then solvent clean with 120 Brushing Thinner to remove residue. Apply two finish coats of Horizons. If the previous coating is soft or in poor condition, remove to the bare surface by sanding or using a paint & varnish remover. Proceed with appropriate bare system as described below. Old tin copolymers must be removed before applying Horizons.

BARE FIBERGLASS: All bare fiberglass, regardless of age, should be thoroughly cleaned with 92 Bio-Blue Hull Surface Prep or de-waxed several times with Pettit D-95 Dewaxer or 120 Brushing Thinner. Sand thoroughly with 80 grit sandpaper to a dull, frosty finish and rewash the sanded surface with 120 Brushing Thinner to remove sanding residue. Then apply two coats of Horizons, following application instructions. Careful observation of the above instructions will help ensure long term adhesion of this and subsequent years’ antifouling paint. To eliminate the sanding operation, prep the surface with 92 Bio-Blue Hull Surface Prep or wash the fiberglass three times using Pettit 95 Dewaxer only. Then apply one thin coat of Pettit 6998 Skip-Sand Primer or 6999 Sandless Primer. Use a 3/16” or less nap when applying by roller. Consult the primer label for complete application and antifouling top coating instructions. Apply two or three coats of Horizons.

BARRIER COAT: Fiberglass bottoms potentially can form osmotic blisters within the gelcoat and into the laminate. To render the bottom as water impermeable as possible, prepare the fiberglass surface as mentioned above (sanding method) then apply three coats of Pettit Protect 4700/4701 High Build Epoxy Primer per label directions. Apply two or three finish coats of Horizons.

BLISTERED FIBERGLASS: See Pettit Technical Bulletin TB-1000 Gelcoat Blister Repair and Prevention Specification for detailed instructions.

BARE WOOD: Sand entire surface with 80 grit sandpaper; wash clean with 120 Brushing Thinner. Apply a coat of Pettit 6627 Tie-Coat Primer thinned 10% to penetrate and seal the wood. Fill any open seams with Pettit Seam Compound and allow an overnight dry. Apply two or three finish coats of Horizons.

STEEL HULLS: Sandblast or disc sand to a clean, bright finish and remove residue with clean, dry compressed air or a clean brush. Immediately apply two coats of Pettit 4700/4701 High Build Epoxy Primer. Read and follow carefully the instructions on the 4700/4701 Epoxy Primer label. If the surface to be painted will be prepared using hand tools such as wire wheels or sanders, clean-off residue and immediately apply one coat of Pettit 6980 Rustlok Steel Primer. Let dry 1-2 hours and follow with two coats of 4700/4701 High Build Epoxy Primer. Read and follow carefully the instructions for application and top coating on both primer labels. Apply two or three finish coats of Horizons.

KEELS - LEAD: Abrade surface to bright metal; clean off residue. Apply one thin coat of 6455/044 Metal Primer; allow to dry six hours. Apply one coat of 4700/4701 High Build Epoxy Primer then, if fairing is required, apply 7050 EZ-Fair Epoxy Fairing Compound. Follow with an additional coat of 4700/4701 High Build Epoxy Primer per label directions. Apply two or three finish coats of Horizons.

KEELS - STEEL OR CAST IRON: Abrade surface to bright metal; clean off residue. Apply one coat of 6980 Rustlok Steel Primer, allowing to dry only 1-2 hours prior to over coating with one coat of 4700/4701 High Build Epoxy Primer. Then, if fairing is required, apply 7050 EZ-Fair Epoxy Fairing Compound followed by one additional coat of 4700/4701 High Build Epoxy Primer, finish with two or three coats of Horizons.

UNDERWATER METAL PARTS: Use the same system as for lead keels.

DO NOT USE THIS PRODUCT ON ALUMINUM HULLS AND OUTDRIVES.

APPLICATION INFORMATION: Horizons is heavily loaded with cuprous oxide. As a result of this loading there is a tendency for settling to occur, especially if the paint has been on the shelf for several months. It is necessary to thoroughly mix the paint before using. If possible, shake the can of paint on a mechanical paint shaker. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in. If mixing is going to be done with a wooden paddle or an electric drill mixer, pour off half of the liquid from the top of the can into another can and then properly mix in any settled pigment; then remix the two parts together thoroughly. Adhere to all application instructions, precautions, conditions, and limitations to obtain optimum performance. Refer to individual labels and tech sheets for detailed instructions when using associated products, etc. Do not thin Horizons more than 10% (12 ounces per gallon) or inadequate paint film thickness will occur and premature erosion of the finish will be likely. Do not apply Horizons in thick films or in more than four coats as poor adhesion may result. When applying by roller use a short nap (3/16 inch maximum) roller cover.

SURFACE PREPARATIONnce, in general, is proportional to the degree of surface preparation. Follow recommendations carefully, avoiding shortcuts. Inadequate preparation of surfaces will virtually assure inadequate coating performance.

MAINTENANCE: Antifouling paint can be effective under all conditions of exposure. Man made pollution and natural occurrences can adversely affect antifouling paint performance. Extreme hot and cold water temperatures, silt, dirt, oil, brackish water and even electrolysis can ruin an antifouling paint. Therefore, we strongly suggest that the bottom of the boat be checked regularly to make sure it is clean and that no growth is occurring. Lightly scrub the bottom with a soft brush to remove anything from the antifouling paint surface. Scrubbing is particularly important with boats that are idle for extended periods of time. The self-cleaning nature of the coating is most effective when the boat is used periodically.

ASSOCIATED PRODUCTS: 120 Brushing Thinner; 121 Spray Thinner; 92 Bio-Blue Hull Surface Prep; 95 Fiberglass Dewaxer; 6998 Skip-Sand Primer; 6999 Sandless Primer; 4100/4101 White Pettit-Protect High Build Epoxy Primer; 4700/4701 Gray Pettit-Protect High Build Epoxy Primer; 6455/044 Metal Primer; 6627 Tie-Coat Primer 6980 Rustlok Steel Primer;7050 EZ-Fair Epoxy Fairing Compound

Related Products