|SKU||Select Your Cable Length||Retail Price||Our Price||Savings|
|tel-SSC13511||11'||$421.40||$365.74||You Save 13%|
|tel-SSC13512||12'||$427.72||$371.17||You Save 13%|
|tel-SSC13513||13'||$434.03||$376.60||You Save 13%|
|tel-SSC13514||14'||$440.35||$382.02||You Save 13%|
|tel-SSC13515||15'||$446.63||$387.42||You Save 13%|
|tel-SSC13516||16'||$452.92||$392.83||You Save 13%|
|TEL-SSC13506||6'||$389.90||$315.08||You Save 19%|
|TEL-SSC13507||7'||$396.19||$320.33||You Save 19%|
|TEL-SSC13508||8'||$402.51||$325.60||You Save 19%|
|TEL-SSC13509||9'||$408.81||$330.85||You Save 19%|
|tel-SSC13510||10'||$419.00||$360.33||You Save 14%|
|tel-SSC13517||17'||$459.24||$372.94||You Save 19%|
|TEL-SSC13519||19'||$471.85||$383.46||You Save 19%|
|TEL-SSC13520||20'||$478.17||$388.73||You Save 19%|
|TEL-SSC13521||21'||$548.85||$447.72||You Save 18%|
|TEL-SSC13522||22'||$556.03||$453.70||You Save 18%|
|TEL-SSC13523||23'||$563.18||$459.68||You Save 18%|
|TEL-SSC13524||24'||$570.34||$465.66||You Save 18%|
|TEL-SSC13525||25'||$584.68||$477.62||You Save 18%|
|TEL-SSC13526||26'||$598.99||$489.57||You Save 18%|
|TEL-SSC13527||27'||$613.33||$501.53||You Save 18%|
|TEL-SSC13528||28'||$627.65||$513.46||You Save 18%|
|TEL-SSC13529||29'||$642.00||$525.44||You Save 18%|
|TEL-SSC13530||30'||$656.32||$537.38||You Save 18%|
Twin rack cables fit SH5210p, SH5230P, SH91610P, and SH91630P helms.
Write Your Own Review
How To Measure
How to Measure Steering Cables “Measure Twice. Order Once.”
Replacement of Existing Cable: If possible, find the part number stamped on the plastic jacket of the old cable. If you removed the old cable, measure for the replacement cable as follows:
For Rotary Steering Cable Replacement, Measure Existing Cable as follows: Measure plastic cable jacket (“Y” dimension, shown in above drawing) in inches, add 18″, and round up to next foot. Order that length cable.
New Installation: Measure cable routing path from wheel center line to engine connection, as follows: A = Center line of wheel to gunwale (or deck, if routed downward), B = Dash to transom, C = Gunwale to centerline of cable connection at centered tiller.
For Cable Installations through the Engine Tilt Tube: Add A, B & C + 6″, then round up to the next foot. Order that length cable.
For Cables Mounted to Transom, Splashwell or Stringer: Add A, B & C, then subtract 6″ and round up to the next foot. Order that length cable.
For Rack Steering Cable Replacement, Measure Existing Cable as follows: Measure plastic cable jacket (“Y” dimension shown in above drawing) in inches, add 30″, and round up to next foot. Order that length cable.
For JBS Jet Boat Cable Replacement, Measure Existing Cable as follows: Measure cable from tip to tip. (Round up to next foot if needed for whole foot.) Order that length cable.
JBS helms are ONLY for smaller jets such as Mercury Sport Jet, OMC Turbo Jet, etc. and look like the helm depicted at right. If your jet steering is different, contact Teleflex. If your engine does not have a tilt tube cable connection as shown at above, see “Connection Kits” pages later in this section to get the information or visit us on-line at www.teleflexmarine.com.
TYPICAL SINGLE STATION ROUTING
A single-cable, starboard drive push-pull mechanical cable system is shown in this diagram. If your mechanical system is different than the one depicted and/or you have any questions about mechanical steering after reviewing this guide, please contact Teleflex (Mechanical) Technical Service at (610)-495-7011 or www.teleflexmarine.com
Cable routings (such as those found on pontoon boats) may vary from this drawing. Confirm length by laying a garden hose or similar object) along cable path and measure run from wheel to engine connection point.