Welcome to WholesaleMarine.com

Call Toll-Free: M-TH 9AM - 8PM FRI 9AM - 6PM EST
1-877-388-2628

Trac Big Water 45 Anchor Winch

Be the first to review this product

SKU: TRC-T10110-45
Availability: In Stock - Ships Today
Order within and your order ships today! Details

Availability: In stock

$239.99 Click for price What's this?
Recent Customer Feedback
 

Product Description

Big Water 45 Electric Anchor Winch

Suitable for larger craft such as deck boats or where excessive winds call for heavier anchors.

 

Big Water 45 Specifics 

  • Maximum Anchor Capacity:  45 lbs.
  • Typical Boat Length:  up to 24'
  • Speed up: 70ft/min
  • Speed down: Free Fall
  • Separate roller davit included
  • Winch Dimensions (LxWxH):  10.1" x 8.3" x 6.5"
  • Davit Dimensions (LxWxH): 6" x 3.5" x 5"
  • Built-in light comes on when anchor is raised or lowered.

 

All Anchor Winch models include:

 

  • Rugged All-Steel Gears
  • 100’ of 0.20” pre-wound braided anchor rope
  • Automatic resetting circuit breaker
  • Sealed membrane UP/DOWN switch
  • 14-gauge marine-grade battery wire which is 17 ft long
  • Anchor safety chain
  • Assembly hardware and instructions
  • 2 Year Manufacturer's Warranty

Additional Information

Manufacturer Trac Outdoor
Manufacture Part Number T10110
UPC 666996101109

Reviews

Write Your Own Review

You're reviewing: Trac Big Water 45 Anchor Winch

  •  
    1 star
    2 stars
    3 stars
    4 stars
    5 stars
    Quality
    Price
    Value

* Required Fields

How to Install

Video from TRAC Outdoor Products website

 

HOW TO INSTALL TRAC BIG WATER 45 ANCHOR WINCH

Protect yourself and others by observing all safety information listed on the instructions.

Tools Required for Installation

  • Electric Drill
  • 5/16’’ (7.9mm) Drill Bit
  • Electrical Terminal Crimping Tool
  • Adjustable Wrench
  • Phillips Screw Driver

Materials Required for Installation

  • Winch and Anchor Roller (included)
  • Seven 8mm bolts, washers and nuts (included) – Longer bolts may be required if your deck is very thick.
  • Shackle for anchor attachment (included)
  • Anchor (not included – up to 30lb. (13.6 kg) recommended, maximum 45 lb. (20.4 kg))
  • Battery Wire and Circuit Breaker (included)

INSTALLING ANCHOR WINCH ON BOAT DECK

  • The anchor winch can be installed on the fore (front) or the aft (rear) of the boat.
  • Locate anchor roller and winch on deck in desired location. The anchor roller must be located at the edge of the deck and must be extended over the edge to allow the anchor to clear the deck when it is docked in the anchor roller.
  • Look below the deck and check for any obstructions underneath the desired anchor roller and winch locations. Make sure there is enough space for the robe spool on the winch to be centered on the anchor roller.
  • Using a marker, mark the anchor roller and winch mounting holes on the deck.

Note: There are several bolt holes in winch frame to choose from. The easiest to use are the 4 slots (2 on each end of the frame). There are also holes for the battery lead wires so you can route the wires through the deck id you desire.

  • Remove winch and anchor roller. Drill the holes. Bolt to deck. Use fender washers and/or marine plywood under the deck to ensure the greatest strength and to spread the load.

WIRING

  • Do not use wire sizes smaller than 14 AWG with 105 degree C rated insulation.
  • The wires and switch are all properly connected.
  • You will need to route the battery wires from the winch to battery and connect the RED positive (+) wire to the silver post on the circuit breaker.
  • The small hole on the buss bar (flat stamped metal part with two holes) is attached to the colored post on the circuit breaker and the large hole on the buss bar is attached to the battery positive terminal.
  • The BLACK negative (-) wire is attached to the battery negative terminal.

ANCHOR ATTACHMENT

  • Attach the shackle to the anchor shank eye.
  • Tie the rope to the anchor shackle.

ANCHOR WINCH OPERATION

  • To lower the anchor press and hold the switch in the “down” position for a few seconds and release the switch.
  • The anchor will freefall to the lake or river bottom.
  • Allow the boat to drift and pull additional rope out of the winch.
  • To stop the rope from coming out of the winch, press the switch UP button for a couple seconds. This will lock the spool and keep it from letting more rope out.
  • To raise the anchor, press and hold the switch in the “up” position.

Information sourced from the TRAC Big Water Anchor Winch User Manual.

You May Also Like