How to Install a Solas Rubex Propeller and Hub Kit

Installing a Solas Rubex propeller involves two jobs. First, fit the interchangeable RBX hub into the propeller housing. Then mount the assembled propeller on the shaft using the hardware specified for your engine or drive.

Whether you’re replacing a damaged propeller or setting up a spare, start by confirming the hub kit part number. The thrust washer, spacer and locking hardware can vary by application, even when two propellers look similar.

Watch How to Install a Solas Rubex Propeller

This Solas walkthrough shows how to change a Rubex propeller. If you’re starting with an empty propeller housing, the second video below shows how to fit the interchangeable hub before mounting the propeller.

What You’ll Need

  • A compatible Solas Rubex propeller and the specified RBX hub kit.
  • The thrust washer, aft spacer, propeller nut and locking hardware specified for your application.
  • A correctly sized prop nut socket, a torque wrench and a sturdy wood block.
  • Gloves, a shop rag and the marine grease specified in your owner’s manual.
  • The installation diagram for your RBX kit and your engine or drive owner’s manual.

How to Choose the Right Rubex Hub Kit

Find the propeller series on the Rubex listing, then check the kit’s application chart for your engine manufacturer, model, horsepower, year or serial range, gearcase size and shaft spline count. The kit needs to fit both the propeller housing and the shaft. Check the individual listing for what’s included, since some applications use original mounting hardware alongside the new hub.

Before You Begin

Secure the boat, shut off the engine, remove the key and shift into neutral. Follow the safety instructions for your engine or drive to prevent accidental starting while you work. Wear gloves when handling the propeller and keep your hands clear of the blades while loosening or tightening the nut.

How to Install a Solas Rubex Propeller and Hub Kit

1. Remove the Old Propeller and Check the Hardware

Remove the cotter pin or release the locking tabs, as applicable. Use a wood block to hold the propeller while you loosen the nut, then support the propeller as you slide it off the shaft. Lay out the hardware in the order it came off. Check whether the forward thrust washer stayed on the shaft or came off with the old propeller, then compare it with the washer shown in the RBX kit diagram.

2. Fit the Rubex Hub Into the Propeller

Use the kit diagram to identify which end of the propeller housing accepts the hub and which way the hub faces. Align it with the cavity and seat it as directed. If it stops short or sits crooked, check its orientation and part number before applying more force.

3. Inspect and Grease the Propeller Shaft

Wipe the shaft clean and check behind the thrust washer for fishing line or debris. Look for damaged splines or signs of gear oil leaking around the shaft seal. Have any damage or leakage inspected before operating the boat. Apply the recommended marine grease to the shaft and install the specified forward thrust washer in the orientation shown in your instructions.

4. Mount the Propeller and Secure the Nut

Align the hub splines with the shaft and slide the assembled propeller into place. Install the aft spacer, washer and nut as shown for your application. Start the nut by hand, use the wood block to hold the propeller and tighten the nut with a torque wrench to the specification in your engine or drive manual. Secure it with the specified locking hardware.

5. Check Propeller Clearance

Remove the wood block. With the engine off and the drive in neutral, turn the propeller by hand and check that it clears the gearcase and trim tab, if equipped. Verify that the nut is locked and the propeller is seated as shown in your instructions. If the propeller rubs or the locking hardware won’t engage, check the fitment and hardware order before running the boat.

Frequently Asked Questions

Does a Rubex propeller come with the hub kit?

Check the individual listing. A Rubex propeller housing may be sold separately from the RBX hub kit, which is selected for the specific engine or drive and propeller series.

Can I reuse my Rubex hub with a new propeller?

Verify that the existing hub kit is specified for the replacement propeller and your engine or drive. Inspect the hub and mounting hardware for damage or wear, especially after a prop strike, and replace any components the instructions call for replacing.

Do I reuse my original thrust washer and prop nut?

That depends on the RBX kit and engine application. Some kits use original hardware, while others specify different components. Compare the hardware with the kit diagram before assembly.

Shop Solas Rubex Propellers and Hub Kits

Browse Solas propellers and Rubex hub kits or use our Propeller Finder to narrow your options by engine. The RBX-102 and RBX-104 listings show how to check the application chart and find the installation instructions for a specific kit.

Need help matching a propeller and hub kit? Have your engine or drive model, serial number and current propeller part number handy when contacting our team.