Garelick 75025S Adjustable Table Base Pedestal

Garelick 75025S Adjustable Table Base Pedestal

This adjustable table base from Garelick easily converts dinettes to berths. The cast aluminum construction provides excellent marine corrosion resistance. A polished aluminum finish will spruce up any vessel. This table base pedestal is able to be adjusted from 15" up to 30".

Features:

• Converts dinettes to berths
• 9"(23cm) diameter cast aluminum base on each end for support
• 2.875" (7cm) smooth stanchion tube
• In lower position inside tube goes below deck 6" (15cm)
• Locks any height from 15" to 30"
• Polished Finish. Smooth. Tube protrudes 6" (15cm) below deck

Table Pedestal Mounting Instructions

1. Locate a place for the mounting pedestal. Ensure there is an open 6" below the deck and no cables or reinforcement ribs are in the mounting area.
2. Set the pedestal on the deck where it will be mounted. Unscrew the locking knob to allow the pedestal to slide. While holding down the inside tube assembly, slide the outside tube up in order to trace around the inside tube. While still holding the inside assembly, slide the outside tube assembly back down to the deck and mark the 6 mounting holes.
3. Cut the center circle in deck. This hole is for the inner tube when the pedestal is in the lower position
4. Drill the six mounting holes in the deck using the proper bit that is compatible with the selected fasteners. NOTE: Fasteners are not provided
5. Place the pedestal on the deck and align the holes in the base with the holes in the deck. Check the pedestal for proper up and down travel
6. Secure the pedestal to the boat deck. This area should be adequately reinforced. Use a backing plate if necessary to make a secure attachment. It is recommended that the fasteners go though both the deck and backing plate for best results.

Table Attachment Instructions

1. Loosen, but do not remove, the locking knob in order to slide the inside tube out of the assembly.
2. Mount the table to the top base using the appropriate fasteners
3. Slide the inside tube back into the assembly. The lock block attached to the knob will need to be aligned with the track on the inside tube.
4. Once inserted, secure the pedestal at the desired height using the tightening knob.

 Click here for Garelick 75025S Adjustable Table Base Installation Instructions

Frequently Asked Questions

What is the Garelick 75025S Adjustable Table Base Pedestal used for?

The Garelick 75025S Adjustable Table Base Pedestal is designed to convert dinettes to berths. Its adjustable design allows the pedestal to lock at any height from 15" to 30", providing flexibility for the table position.

What is the Garelick 75025S Table Base Pedestal made from?

The Garelick 75025S Adjustable Table Base Pedestal features cast aluminum construction with a polished aluminum finish. It has a 9" diameter cast aluminum base on each end and a 2.875" smooth stanchion tube.

How much can the Garelick 75025S Table Pedestal be adjusted?

The Garelick 75025S Table Pedestal adjusts from 15" to 30" and can be locked at any height within that range. In the lower position, the inside tube protrudes 6" below the deck.

What should I check before installing the Garelick 75025S Adjustable Table Base Pedestal?

Before installation, ensure there is an open 6" area below the deck and that there are no cables or reinforcement ribs in the mounting area. The mounting area should also be adequately reinforced, with a backing plate used if necessary for a secure attachment.

Are fasteners included with the Garelick 75025S Table Pedestal?

No. Fasteners are not provided with the Garelick 75025S Adjustable Table Base Pedestal. The supplied installation instructions specify using fasteners appropriate for the deck and mounting application.

How is a table attached to the Garelick 75025S Pedestal?

To attach a table, loosen the locking knob and slide the inside tube out of the assembly. Mount the table to the top base using appropriate fasteners, then slide the inside tube back into the assembly with the lock block aligned with the track. Tighten the knob to secure the desired height.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov