Interlux Micron Extra SPC Antifouling Paint

Interlux Micron Extra SPC Antifouling Paint

Spring 2024 Consumer Rebate program! Save 20$ per gallon up to 2 gallons Feb 1 - June 1! Click here for Additional Information and here for the Rebate Form!

Interlux is known for its high-quality antifouling paints made with superior products and developed for long-lasting results in all types of waters. Interlux Micron Extra Self Polishing Copolymer (SPC) antifouling paint is designed to provide premium multi-seasonal performance in all waters and climates, cold to tropical. The SPC technology provides remarkable protection by polishing away whether at dock or out on the water to provide a smoother more efficient hull while minimizing paint build up.

Interlux Micron Extra SPC is suitable for all types of boats. It can be applied to fiberglass, wood, and previously antifouled surfaces but is not recommended for aluminum boat bottoms. It is available in five popular colors. Two coats are recommended for complete coverage. When applied Interlux Micron Extra SPC antifouling paint dries with a matte finish.

Features:

• For use on fiberglass, wood, and previously painted surfaces. NOTE: Do not use on aluminum.
• Antifouling paint offers multi-season protection year round
• Micron Extra SPC can be launched and relaunched without repainting
• The Self Polishing Copolymer works at a constant rate to for a smoother hull with better efficiency
• Works in Brackish, Fresh, and Saltwater in both cold and tropical climates

Specifications:

• Finish: Matte
• Number of Coats: 2 Coats minimum
• Sizing: 1 US Gallon, 1 US Quart
• Theoretical Coverage: Brush/Roller: 414ft2/gal | Spray: 276ft2/gal
• Colors Available:450 Red, 451 Blue, 452 Black, 453 Dark Blue, 454 Green
• VOC: 328 g/lt average

Associated Products:

• Special thinner 216 - For wiping down previously painted surfaces and thinning
• Fiberglass Solvent Wash 202 - To clean bare fiberglass prior to application
• Interprotect - Epoxy barrier for blister protection, prevention, and priming

Dry Times

*If air temperature falls below 41°F (5°C) during the dry time prior to immersion, extend the dry times 12 hours minimum

How to Apply Interlux Micron Extra SPC Ablative Antifouling Paint

• Application Methods: Air atomized, Brush, Roller
• Recommended DFT per coat
• Brush/Roller: 2.4mils dry per coat
• Spray: 3.6 mils dry per coat
• Recommended WFT per coat
• Brush/Roller: 3.9 mils wet per coat
• Spray: 5.8 mils wet per coat
• Minimum Ambient Temperature: 41°F (5° C)
• Maximum Ambient temperature: 95°F (35°C)

Surface Preparation

Previously Antifouled Surfaces:

• In Good condition: Remove loose paint by sanding with 80 grit paper. Remove sanding residue
• In Poor condition: Remove antifouling paint in poor condition

Bare Fiberglass

• It is very important that bare fiberglass be properly prepared to prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using soap and water to remove loose dirt and contamination.
• Flush with fresh water to remove the soap residue and allow to dry
• Remove mold release wax using one of the following Interlux products: Fiberglass Surface Prep or Fiberglass Solvent Wash 202.
• After the surface has been properly cleaned, follow one of the application systems below.

Fiberglass No Sand System

• Clean the surface following the preparation procedure above.
• Apply one coat of InterProtect 2000E or Fiberglass No-Sand Primer following the label instructions for applying the primer and overcoating with antifouling paint.

Fiberglass Sanding System

• Clean the surface following the preparation procedure above.
• Sand entire surface well with 80 grade paper until flat matte finish is obtained.
• Remove sanding residue.

Blister Prevention System

• Apply the InterProtect system for the prevention of blisters.

Bare Wood

• Sand with 80 grade paper.
• Apply first coat reduced 10% with Special Thinner 216.
• Fill seams, if necessary, with Seam Compound Brown 30.

Click here for Interlux Micron Extra SPC Technical Datasheet

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov