SeaStar Mercury/OMC Jet Boat SSC219 Steering Cable by Dometic
This steering cable is designed for use with Mercury Sport jet or OMC Turbo jet drive steering systems. This SeaStar steering cable features 5/16-24 threaded ends on each side of the cable.
JBS steering cable for the Teleflex jet boat steering helms: SH5087P, SH5088P, SH91691P, SH91692P
** Note: The following helms are obsolete: SH91678P, SH91679P
Direct replacement for Teleflex Marine SSC219 series original factory steering cables. SeaStar Solutions replaced Teleflex Marine and has been acquired by Dometic Group.
Application Info:
Fits Mercury Sport Jet or OMC Turbo jet drives up to 175hp
How to Measure
How to Measure Steering Cables “Measure Twice. Order Once.”
Replacement of Existing Cable: If possible, find the part number stamped on the plastic jacket of the old cable. If you removed the old cable, measure for the replacement cable as follows:
For JBS Jet Boat Cable Replacement, Measure Existing Cable as follows: Measure cable from tip to tip. (Round up to next foot if needed for whole foot.) Order that length cable.
JBS helms are ONLY for smaller jets such as Mercury Sport Jet, OMC Turbo Jet, etc. and look like the helm depicted at right. If your jet steering is different, contact Teleflex. If your engine does not have a tilt tube cable connection as shown at above, see “Connection Kits” pages later in this section to get the information or visit us on-line at www.dometic.com
New Installation: Measure cable routing path from wheel center line to engine connection, as follows: A = Center line of wheel to gunwale (or deck, if routed downward), B = Dash to transom, C = Gunwale to centerline of cable connection at centered tiller.
For Cable Installations through the Engine Tilt Tube: Add A, B & C + 6″, then round up to the next foot. Order that length cable.
For Cables Mounted to Transom, Splashwell or Stringer: Add A, B & C, then subtract 6″ and round up to the next foot. Order that length cable.
TYPICAL SINGLE STATION ROUTING
A single-cable, starboard drive push-pull mechanical cable system is shown in this diagram. If your mechanical system is different than the one depicted and/or you have any questions about mechanical steering after reviewing this guide, please contact Teleflex (Mechanical) Technical Service at (610)-495-7011 or www.teleflexmarine.com
Cable routings (such as those found on pontoon boats) may vary from this drawing. Confirm length by laying a garden hose or similar object) along cable path and measure run from wheel to engine connection point.
Frequently Asked Questions
What is the SeaStar Mercury/OMC Jet Boat SSC219 Steering Cable by Dometic used for?
The SeaStar Mercury/OMC Jet Boat SSC219 Steering Cable by Dometic is designed for Mercury Sport Jet and OMC Turbo Jet drive steering systems. It is a JBS steering cable for Teleflex jet boat steering helms and features 5/16-24 threaded ends on each side of the cable.
Which jet boat drives are compatible with the SeaStar SSC219 steering cable?
The SSC219 is designed for Mercury Sport Jet or OMC Turbo Jet drives up to 175 HP. It is compatible with Teleflex jet boat steering helms including SH5087P, SH5088P, SH91691P, and SH91692P. The SH91678P and SH91679P helms are listed as obsolete.
What type of steering helm does the SeaStar SSC219 use?
The SSC219 is a JBS steering cable for Teleflex jet boat steering helms. JBS helms are intended for smaller jet boats such as Mercury Sport Jet and OMC Turbo Jet applications. Verify that your jet steering system matches the JBS configuration before ordering.
How do I measure an existing cable for a SeaStar SSC219 replacement?
If possible, locate the part number stamped on the plastic jacket of the existing cable. If the old cable has been removed, measure it from tip to tip and round up to the next whole foot if necessary. Order the cable using that rounded measurement.
How do I measure the SeaStar SSC219 steering cable for a new installation?
Measure the routing path from the wheel center line to the engine connection. For installations through the engine tilt tube, add A, B, and C measurements plus 6 inches, then round up to the next foot. For cables mounted to the transom, splashwell, or stringer, add A, B, and C, subtract 6 inches, and round up to the next foot.
What should I verify before purchasing the SeaStar SSC219 steering cable?
Verify that your boat uses a Mercury Sport Jet or OMC Turbo Jet drive up to 175 HP and that the steering system uses a compatible JBS helm. Also confirm the cable connection configuration and required cable length. If your jet steering system differs from the JBS configuration described, the supplied application information recommends contacting Teleflex for assistance.
California Residents: 
WARNING
Cancer and Reproductive Harm -
P65Warnings.ca.gov
