Attwood Battery Tray With Adjustable Hold Downs

Attwood Marine Battery Tray with Adjustable Hold Downs

Lightweight, heavy duty corrosion-resistant polypropylene, non-corrosive black plastic. Includes adjustable-height crossbar and two retaining bolts. Attwood Marine's hold-down trays are designed to secure your battery. Meets ABYC Standard E-10 and U.S. Coast Guard requirements. Patented design. Install with #10 screws.

It fits most 24 Series batteries. Constructed from non-corrosive hi-strength plastic, this battery tray holder measures approximately 11" wide by 7" deep by 2" tall overall. Holds 24 and 24M series batteries.

How to Install Attwood Battery Hold Down Trays

Attwood Battery Hold Down Trays are designed to be used with standard batteries (24/24M & 27/27M series) including Gould 800 Delco Voyager.

The adjustable-height crossbar holds the battery in place. Mounting holes in the tray make it easy to secure and prevent battery movement. The tray is made of noncorrosive, heavy-duty black plastic. Meets ABYC Standard E-10 and U.S. Coast Guard requirements.

Tools and Materials Needed for Installation

• Drill and a suitable drill bit
• Eight #10 stainless steel wood/sheet metal pan head screws
• Eight #10 stainless steel flat washers
• Screwdriver

CAUTION : Battery must be located in a well ventilated area to prevent buildup of explosive gasses. To prevent acid burns, locate in an area away from casual contact.

Mounting Instructions

1. Determine a suitable location for the battery tray making sure there is enough room to work.
2. Using the battery tray as a template, mark the location of the screw holes. It is recommended that you use the mounting holes closest to the retaining bolt threads, if possible.
3. You may wish to further secure the tray with additional screws.
4. Drill eight pilot holes for the screws. Do not drill through the bottom of the boat.
5. Fasten down the tray using the #10 screws and washers.
6. Place the battery into the tray.
7. Thread a bolt into the crossbar on each side. The bolts fit tightly to prevent them from becoming lost when changing batteries.
8. Install the battery retainer and bolts. Tighten moderately until bolts and/or crossbar bend slightly.
9. Connect the battery cables, following the battery manufacturer’s requirements for correct installation. The positive terminal should be insulated to prevent accidental shorting.

CAUTION Overtightening the bolts could damage the threads or damage the crossbar.

Attwood Marine Battery Tray with Adjustable Hold Downs FAQs

What battery sizes does the Attwood Marine Battery Tray fit?

The Attwood Marine Battery Tray is available for 24/24M and 27/27M series batteries.

What is included with the Attwood Marine Battery Tray?

The Attwood Marine Battery Tray includes an adjustable-height crossbar and two retaining bolts.

What material is the Attwood Marine Battery Tray made from?

The Attwood Marine Battery Tray is made from lightweight, heavy-duty, corrosion-resistant polypropylene black plastic.

What standards does this Attwood battery tray meet?

This Attwood battery tray meets ABYC Standard E-10 and U.S. Coast Guard requirements.

What screws are needed to install the Attwood Battery Tray?

Install the Attwood Battery Tray with #10 screws. The installation instructions recommend eight #10 stainless steel wood or sheet metal pan head screws with eight #10 stainless steel flat washers.

How does the battery stay secured in the tray?

The adjustable-height crossbar and retaining bolts hold the battery in place and help prevent battery movement.

Where should a marine battery tray be installed?

Install the battery tray in a well-ventilated area with enough room to work, away from casual contact, and do not drill through the bottom of the boat.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov