This product has been discontinuedShop other Interlux Paint productsThe information provided here has been reproduced courtesy of Interlux Paint Company. Wholesale Marine reproduced this information 2/22/2008.PRODUCT DESCRIPTIONInterlux Outboard and Outdrive Aerosol Primer is formulated for use on underwater areas of aluminium outdrives and outboards, prior to application of Tri-Lux II or Tri-Lux II Aerosol. Outboard and Outdrive Aerosol Primer is a non bleeding, anticorrosive primer that provides an excellent barrier on metal surfaces, reducing galvanic corrosion.PRODUCT INFORMATIONColour Y370-Metallic GoldFinish MatteSpecific Gravity 0.78Typical Shelf Life 2 yrsUnit Size 24 fl.ozDRYING/OVERCOATING INFORMATIONDrying50F 73F 95FTouch Dry [ISO] 2hrs 1hrs 1hrsNote:Launch times are the same as for the antifouling applied.OvercoatingSubstrate Temperature50F 73F 95FAPPLICATION AND USEPreparation BARE ALUMINIUM:Sand with medium grade (grit) emery cloth to a bright metal finish. Immediately apply Viny-Lux Primewash 353/354 thinned 25% with Viny-Lux Solvent 355. Allow to dry for 1-24 hours.PREVIOUSLY ANTIFOULED SURFACE:Sand with 80 grade (grit) paper. Clean with Special Thinner 216. Resand any areas where bare aluminium is exposed with medium grade (grit) emery cloth and wipe clean.MethodImmediately apply Outboard and Outdrive Aerosol Primer to bare areas. At least 2 coats should be applied. Hold can 12-16 inches from the unit when applying the paint. After minimum overcoating time has been exceeded, wipe with Special Thinner 216 and sand before applying more coats. Continue until the entire can has been used per outdrive.HintsMixing Shake can well, listening for mixing ball. Continue shaking for at least 1 minute.Some Important PointsDo not use above the waterline. Product temperature should be minimum 10C/50F and maximum 35C/95F. Ambient temperature should be minimum 10C/50F and maximum 35C/95F. Substrate temperature should be minimum 10C/50F and maximum 35C/95F.Compatibility/SubstratesApply to clean, dry, properly prepared surfaces only. Do not use under vinyl based antifouling paints such as VC Offshore or Baltoplate.Number of Coats 2Recommended DFTApplication Methods Aerosol canTRANSPORTATION,STORAGE AND SAFETY INFORMATIONTRANSPORTATION:Outboard and Outdrive Aerosol Primer should be kept in securely closed containers during transport and storage.STORAGE:Exposure to air and extremes of temperature should be avoided. For the full shelf life of Outboard and Outdrive Aerosol Primer to be realised ensure that between use the container is firmly closed and the temperature is between 5C/40F and 35C/95F. Keep out of direct sunlight.Safety DISPOSAL:Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal. Remainders of Outboard and Outdrive Aerosol Primer cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.GENERAL:Read the label safety section for Health and Safety Information, also available from our Technical Help Line.IMPORTANT NOTESThe performance of any marine paint or coating depends on many factors outside the control of International Paint Inc., including surface preparation, proper application, and environmental conditions. Therefore, International Paint Inc. cannot guarantee this product's suitability for your particular purpose or application. IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND/OR MERCHANTABILITY ARE EXCEEDED. International Paint Inc. SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. By purchase of this product, the buyer agrees that the sole exclusive remedy, if any, is limited to the refund of the purchase price or replacement of the product at International Paint Inc. option.Interlux and International are registered trademarks of Akzo Nobel. #Application Instructions #DIY #Interlux #Paint