This product has been discontinued Shop other Interlux Paint products This information provided here has been reproduced courtesy of Interlux. Wholesale Marine reproduced this information on 3/24/2010. PRODUCT DESCRIPTION * Hybrid formulation combines classic tung oil with fast-drying polyurethane * Excellent resistance to abrasion, oils and chemicals * Easy to apply, high gloss amber finish * Contains HALS and UV absorbers * Suitable for all internal and external woods, including oily timbers such as Teak PRODUCT INFORMATION Colour YVA501 Finish High Gloss Specific Gravity 0.9 Volume Solids 42 percent Typical Shelf Life 2 yrs VOC (As Supplied) 453 g/lt Unit Size 1 US Pint (USA) 1 US Quart (USA and Canada) APPLICATION AND USE Preparation PREVIOUSLY VARNISHED WOOD: In Good Condition: Clean with thinners. Sand smooth with 280-320 grade paper. Remove sanding dust with thinners. In Poor Condition: Remove all previous coatings. Apply a minimum of 3-5 coats. Sand every 2-3 coats, using 320-400 grade paper.* Remove sanding dust with a dust wipe. BARE WOOD: Sand smooth with 80-180 grade paper and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying the first coat. OILY WOODS e.g. Teak: Must be adequately degreased (Brushing Liquid 333 is recommended) and prepared prior to application of Compass. Ensure the surface is completely dry before applying the first coat. Prime, if required, with Clear Wood Sealer. Brush/Roller: If Clear Wood Sealer has been omitted, thin the first coat 30 percent with Brushing Liquid 333. Subsequent coats can be thinned up to 15 percent dependent upon ambient temperature, application conditions and personal preference. Apply a further 3-5 coats (brush)/ 4-6 coats (roller), until satisfactory finish is achieved. Sand every 2-3 coats, using 320-400 grade paper.* Remove sanding dust with a dust wipe. * Initial aesthetics may be further improved by sanding between every coat. Method Pour the amount you expect to use in a separate container. Avoid using direct from the can. Strain it through a paint strainer to ensure there is no contamination. Do not apply too thickly. Hints Mixing Stir thoroughly before use. Thinner Brush - Brushing Liquid 333. Spray - Special Thinner 216. Thinning Thin the first coat by 30 percent using recommended thinner. Subsequent coats can be thinned up to 15 percent dependent upon ambient temperature, application conditions and personal preference to allow best finish. Cleaner Brushing Liquid 333 Conventional Spray Pressure Pot: 1-2 bar 14.5-29 psi (gun pressure), 8-10 psi (air pressure) Tip Size: 1.2-1.4 mm/ 47-54 thou. Thin 20-25 percent with Special Thinner 216. Brush Always use a clean brush that is kept specifically for varnishing. Clean brushes before use. Roller If rolling, use a thin nap roller and "tip-off" with a clean natural bristle brush or pad otherwise air bubbles may become trapped in the film. Other Spray pressures listed are recommendations only. The applicator may use any settings which yield the best results for the individual spraying technique and current weather conditions. Avoid using direct from the can. Pour the amount you expect to use in a separate container. When applying Compass by brush or roller, it may be necessary to adjust the number of coats applied to ensure the total specified system dry film thickness is achieved. Some Important Points Never leave bare wood exposed for long periods of time as it will absorb moisture. Do not use straight from can otherwise contents will age prematurely. Failure to follow proper dry times carefully will cause improper drying, wrinkling and loss of adhesion. Avoid painting in direct sunlight. Use above the waterline only. Only use recommended thinners. If maximum overcoating times are exceeded, sand with 280-320 grade paper. Product temperature should be minimum 15 degrees C/60 degrees F and maximum 30 degrees C/86 degrees F. Ambient temperature should be minimum 5 degrees C/41 degrees F and maximum 35 degrees C/95 degrees F. Substrate temperature should be minimum 5 degrees C/41 degrees F and maximum 35 degrees C/95 degrees F. Compatibility/Substrates Suitable for use on all types of wood including oily timbers such as Teak. Do not apply two part varnishes over one part varnishes. Number of Coats Previously varnished wood: mimimum 3 unthinned coats (5 coats if thinned). Bare wood: 1 thinned coat, then 3-5 unthinned coats (5-7 coats if thinned). Coverage (Theoretical) - 582.1 (ft2/Gal) (Practical) - 525.1 (ft2/Gal) Recommended DFT 1.2 mils dry by brush Recommended WFT 2.8 mils wet by brush Application Methods Brush, Conventional Spray, Roller TRANSPORTATION,STORAGE AND SAFETY INFORMATION Storage GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of this product to be realised ensure that between use the container is firmly closed and the temperature is between 5 degrees C/40 degrees F and 35 degrees C/95 degrees F. Keep out of direct sunlight. TRANSPORTATION: Compass should be kept in securely closed containers during transport and storage. Safety GENERAL: Always use gloves and goggles and keep skin protected with overalls. Users should ensure they have a copy of the Material Safety Datasheet for this product and that they are familiar with all the safety directions before use. Read the label safety section for Health and Safety Information, also available from our Technical Help Line. DISPOSAL: Do not discard tins or pour paint into water couses, use the facilities provided. It it best to allow paints to harden before disposal. #Application Instructions #DIY #Interlux #Paint
