Total Price:Add to Cart
Interlux Watertite 2-Part Epoxy Marine Filler Compound
Interlux Watertite is a quick drying 2-part epoxy filler suitable for use on Fiberglass, Metals, Epoxy and rigid Wood constructions. The formulation does not shrink and is
extremely water resistant, making it suitable for osmosis damage repairs. It has a long easy-to-sand window and can be applied to a thickness of 3/4" without sagging. Its superior spreadability makes it an ideal glazing compound for filling small nicks and scratches.
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
APPLICATION DATA METHOD: Spatula / Putty Knife
DRY FILM THICKNESS PER COAT: 63.5 mils
COVERAGE: 25 sq. ft/gal.
APPLICATION TEMP: 45°F Min. / 95°F Max.
THINNER: Do Not Thin
|Temp||To Touch||Sandable||To Launch||Pot Life||To Recoat|
|95°F||20 MIN||3 HR||36 HR||10 MIN||10 HR|
|73°F||35 MIN||5 HR||2 DAY||15 MIN||5 HR|
|50°F||50 MIN||8 HR||5 DAY||25 MIN||4 HR|
Note: At 7°C/45°F the pot life is 30 mins and the product is sandable after 24 hrs, immersion after 6 days.
METAL: Above water: Pre-prime with Viny-Lux Primewash 353/354. Apply one coat of Epoxy Primekote. Sand surface with 80-120 grade (grit) paper, wipe clean. Apply Watertite*. Below water: Prime with Interprotect 2000E or Interprotect 3000.
BARE FIBERGLASS: Clean with Fiberglass Surface Prep YMA601 or Fiberglass Solvent Wash 202. Sand with 80 grade (grit) paper. Remove sanding residue.
APPLICATION INFORMATION: Mix in a 1:1 ratio by volume it is important to ensure the correct volume mix ratio is used. Mix the two components thoroughly to an even colour. Do not use below 7°C. Do not apply more than ¾" thickness at any one time. Product temperature should be minimum 10° C/50°F and maximum 35°C/95°F. Ambient temperature should be minimum 7°C/45°F and maximum 35°C/95°F. Substrate temperature should be minimum 7°C/45°F and maximum 35°C/95°F. Apply using a trowel, spatula or putty knife. When the product has cured, wash with fresh water and sand with 80 grade (grit) paper. Apply to clean, dry, properly prepared surfaces only. Watertite* must be overcoated with VC Tar, VC Performance Epoxy, Interprotect 2000E/2001E or Interprotect 3000/3001. Do not apply topside finishes, polyester or vinylester materials over Watertite*.
California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov
Permanent repair of fiberglass, wood, metal, stucco and drywall. High quality, white plastic filler for filling dents, scrapes and gouges. This product does not shrink after curing. A true "miracle...Choose Options
Interlux Brightside - High Gloss Polyurethane Topside Marine Paint Brightside Polyurethane is a hard, high gloss one-part polyurethane topside finish. Excellent application characteristics yield...Choose Options
Interlux Interprotect Epoxy Barrier Coat Kit - Gray Interprotect 2000E is a unique two part epoxy coating, developed to protect new and used fiberglass hulls from water absorption. Microplates...Choose Options
Marine Tex Epoxy Putty Repair Kit - White Marine-Tex is a heavy-duty structural epoxy, used to repair aluminum, fiberglass and wooden boats, reinstall loose or stripped fasteners, permanently bond...Choose Options
Interlux Perfection 2-Part Polyurethane High Gloss Marine Paint Interlux Perfection is a high-gloss two-part polyurethane finish. Its high performance formula combines a long lasting abrasion and...Choose Options
Pettit Easypoxy (EZ-Poxy) High Gloss Topside Marine Paint Pettit Easypoxy is a modern Polyurethane Paint that is easy to apply. One part application, long lasting, and provides fantastic gloss...Choose Options
Interlux Pre-Kote Brightside Boat Primer Interlux Pre-Kote primer is used above the waterline prior to painting topsides with Brightside, Premium Yacht Enamel or any one-part topside finish on wood,...Choose Options
Interlux Interprotect Epoxy Barrier Coat Kit - White Interprotect 2002E is a unique two part epoxy coating, developed to protect new and used fiberglass hulls from water absorption. Microplates...Choose Options