Pettit Easypoxy High Gloss Topside Marine Paint

Pettit EZ Poxy High Gloss Topside Marine Paint

Pettit Easypoxy delivers professional-grade protection for above-waterline boat surfaces with its advanced polyurethane formula. This high-gloss topside paint resists fading, chalking, and UV damage while standing up to saltwater, weather exposure, and general wear. The self-leveling formula applies smoothly by brush, roller, or spray, covering up to 600 square feet per gallon. Available in 34 colors with quart and gallon sizes, it works on properly prepared fiberglass, wood, and metal surfaces. Apply at least two coats between 50°F and 90°F for optimal results and long-lasting durability in harsh marine conditions.

NOTE: Ground-shipped within the Continental U.S. only.

Features

• High-Gloss Finish: This high-gloss marine paint creates a stunning finish that resists fading and chalking, providing a durable and sleek aesthetic. Its UV-resistant properties prevent fading even with constant sunlight exposure.
• Durable and Weather-Resistant Formula: Pettit topside paint is formulated to withstand the harsh marine environment. Its durability protects against abrasion, scratches, and wear caused by exposure to saltwater, wind, and weather.
• Easy Application: Both experienced boaters and beginners can apply Pettit EZ Poxy to achieve a professional finish. Use a brush, roller, or sprayer, and let its self-leveling properties and user-friendly formula achieve stunning results. 

Specifications

• Finish: High-gloss
• Coverage: Up to 600 sq. ft/gal.
• Number of Coats: At least two coats minimum
• Colors: 34 colors available; refer to our Pettit paint color chart
• Pack Size: Available in one quart for all colors and one gallon for White, Hatteras Off-White and Semi-Gloss White

Associated Products

To get the best results, pair your Pettit EZ Poxy with these products:

• Pettit 120 Thinner: Use for brushing, rolling, and clean-up
• Pettit 121 Thinner: Use for spraying
• Pettit Satin Additive: Achieve a semi-gloss to semi-flat finish that reduces glare on deck surfaces and interiors.
• Pettit EZ-Prime: Before applying Pettit topside paint, apply a primer as a base coat, particularly on surfaces that are aged, cracked, checked, pitted, rough, or not fully smooth, to ensure optimal adhesion and a flawless finish.

How To Apply Pettit Easypoxy Topside Paint

1. Pettit EZ Poxy is best applied in temperatures between 50°F and 90°F, with low humidity and no rain. Avoid painting in direct sunlight or extreme heat, which may affect drying and leveling.
2. Prepare your surface for paint application. Refer to our “Non-Fiberglass Surface Preparation” guide below.
3. Stir the paint thoroughly before use.
4. Apply a thin, even coat with a brush, roller, or spray, and let it dry overnight.
   
5. Lightly sand with 220 grit sandpaper.
6. Apply a second coat and let it cure for 8 to 24 hours, depending on your area’s temperatures.

Application Notes

• Dry Film Thickness per Coat: 1.5 mils (3 wet mils)
• Coverage: 600 sq. ft/gal.
• Application Temp: 50°F Min. / 90°F Max.
• Avoid applying multiple coats in a single day. Applying excessively thick layers over 4 wet mils can prevent proper drying and produce a soft, under-cured paint film.
• Avoid painting on extremely humid days (90°+ RH) or when it’s raining.
• Avoid painting outdoors in the late afternoon, as dew can negatively impact the wet paint film and compromise the finish.
• In cooler temperatures, ensure that the air and surface temperatures stay at or above 50°F for at least 8 hours after application to allow proper curing.

Although thinning Pettit EZ Poxy paint is not recommended for brush or roller applications, up to 10% of Pettit 120 Brushing Thinner can be added in hot weather to help maintain a wet edge. For optimal results on large, smooth surfaces, use a short roller and level it with the tip of a brush.

For traditional spray applications, thin Pettit EZ-Poxy using 15 to 20% of Pettit 121 Spraying Thinner. For airless sprays, use up to 5% and a tip size between 0.11 and 0.15 inches in diameter for proper application.

Click to Download Pettit Easypoxy Application Instructions

Surface Preparation

Fiberglass Application 

Non-Fiberglass Application 

Bare Wood

1. Sand bare wood with 80 to 120 grit sandpaper until smooth. If the wood has been epoxied, scrub thoroughly with an ammonia/water solution, sand with 120 grit, and clean with Pettit 120 Thinner.
2. Use 7050 EZ-Fair Epoxy Fairing Compound to fill screw heads or small holes. Sand the filled areas flush and clean with the same thinner.
3. Apply a coat of 2018 EZ WoodSealer to seal the porous grain. For epoxied wood, skip the sealer and move directly to priming.
4. Apply one or two coats of 6149 EZ Prime, sanding each coat with 80-120 grit sandpaper and cleaning with Pettit 120 Thinner between coats until a smooth base is achieved.
5. Once the primed surface is clean and smooth, proceed with the first coat of Pettit Easypoxy for a durable, high-gloss finish.

Steel Hulls

1. Clean the surface to a bright finish by sandblasting or grinding, then remove any blast residue.
2. Apply a coat of 6980 Rustlok Primer and let it dry until tacky. For rough surfaces, apply a coat of 6627 Tie-Coat Primer. Sand before cleaning with Pettit 120 Thinner.
3. Repeat as needed until smooth, then apply the first coat of Pettit EZ Poxy.

Aluminum

1. Remove oil and grease using Pettit 120 Thinner.
2. Use a medium-grit emery cloth to remove oxidation, etch the surface, and then clean off any sanding residue.
3. Apply a thin coat of 6455/044 Metal Primer and let it dry for at least two hours. Optionally, use 6149 EZ Prime for additional smoothing before applying the first coat

Frequently Asked Questions

What is Pettit EZ Poxy High Gloss Topside Marine Paint used for?

Pettit EZ Poxy High Gloss Topside Marine Paint is a high-gloss topside coating for properly prepared fiberglass, wood, and metal surfaces. Its self-leveling formula can be applied by brush, roller, or spray and is designed to provide a durable finish that resists fading, chalking, UV exposure, abrasion, scratches, and general marine wear.

How many coats of Pettit EZ Poxy should be applied?

Apply at least two coats of Pettit EZ Poxy. Apply a thin, even first coat and allow it to dry overnight, then lightly sand with 220-grit sandpaper before applying the second coat. Avoid applying multiple coats in one day or building the coating beyond 4 wet mils, as excessive thickness can interfere with proper drying.

What surfaces can Pettit EZ Poxy High Gloss Topside Marine Paint be applied to?

Pettit EZ Poxy can be used on properly prepared fiberglass, wood, and metal surfaces. Bare wood should be sealed and primed, while steel and aluminum require the specified surface preparation and primers. The product is intended for properly prepared topside surfaces.

What temperature is recommended for applying Pettit EZ Poxy?

Apply Pettit EZ Poxy when the air and surface temperatures are between 50°F and 90°F. Avoid rain, direct sunlight, extreme heat, and very high humidity. In cooler conditions, keep the air and surface at or above 50°F for at least 8 hours after application to support proper curing.

Can Pettit EZ Poxy be thinned for brush, roller, or spray application?

Thinning is generally not recommended for brush or roller application, although up to 10% Pettit 120 Brushing Thinner can be added in hot weather to help maintain a wet edge. For traditional spray application, use 15-20% Pettit 121 Spraying Thinner. Airless spray application can use up to 5% thinner.

How much area does Pettit EZ Poxy cover, and what colors are available?

Pettit EZ Poxy provides coverage of up to 600 square feet per gallon and is available in 34 colors. All colors are available in one-quart sizes, while one-gallon sizes are available for White, Hatteras Off-White, and Semi-Gloss White.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov