Sea Hawk Monterey Bottom Paint

Sea Hawk Monterey Water-Based Bottom Paint

Sea Hawk's Monterey Antifouling Paint is a water-based, semi-hard ablative coating for vessels of all sizes and hull substrates. This premium bottom paint has been a leader in environmentally friendly antifouling protection for over a decade. Monterey paint is easy to apply, emits low VOC's, and contains the highest grade of cuprous oxide available. Its semi-hard ablative properties means it lasts longer and self-polishes to keep your hull smooth and barnacle-free. Monterey is also the perfect paint for boats stowed out of the water because its antifouling power is not reduced by removal from the water. Sea Hawk Monterey Bottom Paint can be applied over most existing bottom paint in good condition.

Features:

• Consistent viscosity allows for a better flow and rolling ability
• Low VOC's and highest grade of cuprous oxide available
• Semi-Hard ablative finish to have lasting finishes on high speed vessels
• Better color consistency for color matching
• May be applied over most existing bottom paints
• Proven to outperform other water-based paints
• Easy cleanup with soap and water

Specifications:

• Finish: Semi-gloss
• Copper Content: 54.67%
• VOC: 78 grams/liter
• Coverage: 320 sq. ft./gal.
• Number of Coats: 2-3
• Colors Available: 5545-Black, 5430-Dark Blue
• Pack Size: 1 US Gallon

How to Apply Sea Hawk Monterey Bottom Paint

Sea Hawk Monterey Bottom Paint is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap 3/8” roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 10% using water. Monterey has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.

• Finish: Semi-Gloss
• Coverage:  320 Sq Ft
• Application Method: Brush, Rolling, Airless Sprayer
• Maximum Roller Thickness: 3/8” Nap
• Number of Coats: 2
• Wet Film Thickness: 5.0 mils
• Dry Film Thickness: 2.2 mils
• Application Temp: 50° F Min/ 95° F Max
• Thinner: Water

Surface Preparation and Application

Previously Painted Surfaces

• Known Compatibility of existing antifoulant
• Power wash to remove any loose paint or other contaminants.
• Apply minimum 2 coats of Monterey. Allow 3-6 hours between coats and a minimum overnight dry.
• Unknown Compatibility of existing antifoulant
• Power wash to remove any loose paint or other contaminants.
• Scuff sand with 80 grit sandpaper, remove all residue and let dry.
• Apply 1 coat of 1277 Barrier coat primer or 1283 Island Primer
• Apply minimum of two coats of Monterey. Allow 3-6 hours between coats and a minimum overnight dry.
• Poor condition of existing antifoulant
• If previous coating is cracking, peeling, or flaking strip the antifoulant with stripper, sanding, or commercial blasting.
• Once stripped refer to the Bare Fiberglass Application Guidelines.

Bare Fiberglass

• To prepare the surface it is important to remove all contaminants first. Scrub the surface with detergent soap and a stiff brush.
• Using either S-80 Wax N’ Grease Killer or S-90 De-Wax Etch & Cleaner scrub the surface and rinse thoroughly.
• Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner
• Once cleaned and sanded, seal the surface with 2-3 coats of Tuff Stuff. Apply the second coat once the first has a tacky feel.
• Apply minimum of two coats of Monterey. Allow 3-6 hours between coats and a minimum

Sanding Method:

• Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner
• Apply minimum of two coats of Monterey. Allow 3-6 hours between coats and a minimum overnight dry.

Non-Sanding Method:

• Apply one thin coat of Sea Hawk 1266 no more than .3-.5 mils wet film thickness and allow to dry for 1 hour.
• Apply minimum of two coats of Monterey. Allow 3-6 hours between coats and a minimum overnight dry.

Bare Wood

• Clean the surface and ensure it is dry and free of contaminants.
• Sand to a uniformly frosty, dull looking surface with 80-100 grit sandpaper.
• Apply two coats of Monterey. Apply first coat thinned 20% and let dry overnight.
• Apply two more coats allowing 3-6 hours between coats and a minimum overnight dry.

Steel/Aluminum Hulls

• Sandblast to near white or white metal SSPC-SP-10 or equivalent. Remove residue by brush or compressed air.

Copper Based Antifoulant Application

• Apply two coats of S-76 Primer, the first coat applied within 1 hour of sanding. Allow the first coat to dry to a tacky feel then apply second coat.
• Seal the surface by using 3-4 coats of Tuff Stuff. Apply the first coat within 8 hours of applying the last coat of S-76.
• Apply minimum of two coats of Monterey, allow 3-6 hours between coats.

Copper-Free Antifouling Application for Aluminum Only

• Seal the surface with 2 coats of Tuff Stuff. Apply the first coat and allow the surface to dry to a tacky finish. 
• Apply minimum of two coats of Monterey, allow 3-6 hours between coats and a minimum overnight dry.

Above information sourced from Sea Hawk Bottom Paint Application Instructions

Click Here to Download Sea Hawk Monterey Bottom Paint Application Guide

Click Here to Download Sea Hawk Bottom Paint Compatibility Chart

Frequently Asked Questions

What kind of protection does Sea Hawk Monterey provide?

Sea Hawk Monterey is a water-based, semi-hard ablative bottom paint designed to provide antifouling protection while maintaining a smooth hull surface. Its self-polishing finish helps reduce paint build-up and supports long-lasting performance on a wide range of vessels.

Is Sea Hawk Monterey easy to apply and clean up?

Yes. Sea Hawk Monterey is a water-based formula that can be applied by brush, roller, or airless sprayer, and it cleans up easily with soap and water.

Can Sea Hawk Monterey be applied over existing bottom paint?

Yes. Sea Hawk Monterey may be applied over most existing bottom paints when the previous coating is in good condition. When compatibility is unknown or the previous coating is in poor condition, the recommended preparation and primer system should be followed.

How much coverage does Sea Hawk Monterey provide?

Sea Hawk Monterey provides approximately 320 square feet of coverage per gallon. Actual coverage can vary depending on surface condition, application method, and film thickness.

How long should Sea Hawk Monterey dry before launch?

At 73°F and 95°F, Sea Hawk Monterey requires a minimum of 12 hours before launch. Always allow proper drying between coats and follow the full application instructions.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov