Jack Plates

T-H Marine CMC PT-35 Hydraulic Tilt and Trim The CMC PT-35 Electric Hydraulic Tilt & Trim delivers precise boat handling for outboard motors up to 35 HP. This compact 24-pound unit features durable 6061-T6 extruded aluminum construction with...

Add to Cart

T-H Marine CMC ML-65 Manual Power-Lift Transom Jack Plate - 5-1/2" Set Back Transom jacks are used to adjust the motor higher out of the water for optimal shallow water performance. This essentially provides less drag on the boat. The addition of the...

Add to Cart

T-H Marine CMC High Speed Hydraulic Power-Lift Transom Jack - 5-1/2" Set Back CMC High Speed Hydraulic Transom Jack is ideal for fresh or salt water use. Made of 6061 T6 alloy aluminum extrusions and fastened with stainless steel fasteners. This transom...

Add to Cart

T-H Marine Hi-Jacker Jack Plate The T-H Marine Hi-Jacker Jack Plate is the most recognized brand name in the industry. This plate is constructed of tough 3/8" aircraft aluminum and features a design that allows full tilt with dual steering. All bolts...

Add to Cart

CMC Manual Power-Lift Transom Jack 10" Set Back Features: One Piece Design Made of 6061 T6 Extruded Aluminum Alloy Stainless Steel Fasteners for Maximum Strength and Durability Centrally Located Adjustment Screw for Positive Alignment 10" Set...

Add to Cart

CMC 2 Piece Manual Power-Lift Transom Jack 5-1/2" Setback Features: 5-1/2" Set Back The 2 piece adjustable manual has 5 inches of slot adjustment at the motor mounting bracket and 1-1/2 inches of adjustment at the transom bracket.

Add to Cart

T-H Marine CMC PT-130 Electric Hydraulic Tilt and Trim The CMC PT-130 is a tilt and trim unit designed for use with 130HP motors and smaller. Constructed from 1/2" 6061 T6 extruded aluminum with stainless steel hardware for outstanding corrosion...

Add to Cart

T-H Marine CMC 5 Inch Motor Mount Vertical Extension Boat motor mounts have several uses. Primarily these extensions are used to convert from a propeller-driven craft to a jet drive. An alternate purpose allows the extension to be mounted on shallow...

Add to Cart

T-H Marine Pro Hi-Jacker Jack Plate The T-H Marine Pro Hi-Jacker is a 3/8" thick aluminum jack plate designed for V-6 Outboards with a maximum of 175 HP. Locking bars inside allow for the side locking bolts to be adjusted from the outside using a single...

Add to Cart

Bolt kit for mounting outboard engine to jack plates or tilt & trim units. Kit contains: - 4 each 1/2"-13 x 3" long bolts - stainless steel - 4 each 1/2"-13 lock nuts - brass with nylon insert - 8 each 1/2"-flat washers - stainless steel

Add to Cart

Atlas Micro Hydraulic Jack Plate The Atlas Micro Hydraulic Jack plate is the lightest and smallest hydraulic jack out there. Great for smaller boats. Specifications: Only 23 lbs. Self contained hydralics Maximum horsepower: 115 HP 4"...

Add to Cart

CMC BA-130 Breakaway Unit The CMC BA-130 Breakaway unit is designed for duck hunters and/or fishermen that use their boats in shallow stumpy areas. It allows small boats and motors to slide over submerged logs or debris at low speeds to get to the...

Add to Cart

T-H Marine CMCTransom Clamp Adapter for PT-130 This adapter kit is made for quick and easy installation of these transom clamp type of motors. Works with CMC PT-130 Tilt & Trim, ATLAS THT-130C Tilt & Trim (our larger trim units sized...

Add to Cart

Bob's Machine Hydraulic Pump Assembly The Bob's Machine Hydraulic Pump Assembly comes complete with solenoids, wiring harness, aluminum backing plate, and two stainless steel 90 degree fittings. The included pump comes with a 3 year manufacturer's...

Add to Cart

CMC High Speed Hydraulic Power-Lift Transom Jack 5-1/2" Set Back - T-H-65301 The dependable, self-contained and water proof CMC High Speed Hydraulic Power-Lift Transom Jacks have a maximum lifting capacity of 7853 pounds of thrust, more than any...

Add to Cart

CMC PT-130 Electric Hydraulic Tilt and Trim with Gauge Features: Rated for 130 HP and Smaller Motors. 6" Set Back to Enhance Boat Stability and Performance. 20 Degrees of Trim and a Total of 90 Degrees of Tilt and Trim. 1/2" 6061 T6 Extruced...

Add to Cart

Bob's Machine Extreme Gen 3 Action Series Hydraulic Jack Plate 6" Setback Bob's Machine Extreme Gen 3 Jack Plates are designed for 550+ HP engines including V8's. This series of jack plates is wider, allowing for Verado installation without the use of...

Add to Cart

Bob's Machine Kick-Back Jac Plate The Bob's Machine Kick-Back Jac Plate, aka "Stump Jumper" provides a 45 degree tilt up (kick up) for motors up to 115 HP. Delrin rollers and bearings provide a long life of smooth operation and pivoting without the need...

Add to Cart

CMC Hydraulic Power-Lift Transom Jack 5-1/2" Set Back Features: No Gauge Included Model PL-65 Rated for V-6 and Smaller Motors Provides 5" of Vertical Travel Not designed for V8 Motors or Racing Applications

Add to Cart

Bob's Machine 100-105100 Hydraulic Kick-Back Jac Plate - Action Series Hydraulic Kick-Back Jac Plate allows you to jack up your motor and idle over obstructions, preventing costly damage to the lower unit. This hydraulic kick-back jack plate...

Add to Cart