Interlux Sikkens Cetol Marine Natural Teak Finish

Interlux Sikkens Cetol Marine Natural Teak Finish

Over time, all the potential environmental hazards, such as saltwater, wind, and scorching sun rays, can have their way with teak furniture and decking. Protect your investment with Sikkens Cetol Marine Natural Teak Finish. Cetol Marine’s Natural Teak formula actually enhances the natural wood grain, while its specially formulated UV- absorbing technology provides added protection with a durable, translucent, and protective wood finish. Sikkens Cetol marine natural teak is designed for use above the waterline on all interior and exterior woods. Sikkens Cetol Marine’s proprietary Next Wave technology features a unique UV-absorbing package, made from specialty resins and advanced UV absorbers. These special alkyd resin compounds and high-quality synthetic UV-absorbing pigments combine to create a “sunscreen” for enhanced color retention and wood protection.

What is Next Wave technology?

Next Wave technology is a UV-absorbing formula that acts as a sunscreen, ro protect wood by deflecting the damaging effects of the sun's UV rays. Next Wave will extend the longevity of the wood’s finish and enhance its color retention. The unique UV-absorbing finish in Sikkens Cetol Marine products protects the natural finish of wood and extends the beauty of the finish and the service life of your teak deck or deck furniture.

Cetol Marine Natural Teak Finish can be used on exterior and interior hardwoods such as teak, mahogany, and oak. Sikkens Cetol Marine products should only be applied above the waterline.

Specifications:

• Finish: Satin
• Number of Coats:2-3
• Coverage:Approx. 360 ft²/gal

How To Apply Sikkens Cetol Marine Natural Teak Finish

Follow preparation procedures	One coat Cetol Natural Teak	Allow 24 hours for drying	One coat Cetol Natural Teak	Allow 24 hours for drying	One coat Cetol Natural Teak

• Application: Use a long haired natural bristle brush. Apply in the direction of the grain.
• Number of Coats: 3

Application Dos: Apply when temperature is between 50°F and 95°F. Saturate all end grains. Apply liberal coats and maintain a wet edge. For best results, apply in the direction of grain with a long haired natural bristle brush.

Don't apply In direct sunlight or when the surface is hot to touch. Do not apply in wet weather or when moisture content is greater than 18%. Do not apply Sikkens Cetol Natural Teak Finish below the waterline.

Surface Preparation:

• New Exterior/Interior Wood:
• Wipe the wood with Interlux Special Thinner 216 to remove any natural surface oils and contaminants. Once dry, sand the surface with 180-220 grit sandpaper, always sand along the length of the grain. Remove all sanding dust by vacuuming the surface.
• Wipe the surface with Interlux Special Thinner 216 and allow it to dry before applying Sikkens Cetol Marine products.
• Note: If the wood is exposed for more than 24 hours, clean the surface again with Interlux Special Thinner 216 in order to remove any surface contaminants
• Exterior/Interior - Previously Coated Wood (Non-Cetol Marine Products):
• Remove all existing coatings before applying Cetol. To remove old coating, either sand with 120-180 grit sandpaper or use Interlux Inter strip 299E chemical stripper specifically designed for marine use.
• Once the previous coating is removed, follow instructions for New Exterior/Interior Wood.
• Exterior – Weathered Wood or Previously Oiled Wood:
• To ensure proper adhesion of Cetol products on weathered or previously oiled wood, use Interlux Premium Teak Restorer with a nylon scuffing pad as per instructions on label.
• Be sure to rinse the wood well with clean water to remove surface dirt and allow it to dry thoroughly. This should be followed by the preparation procedures for New Exterior/Interior Wood.
• Blue Fungi and Mildew:
• Persistent blue fungi or mildew may be treated by using Teak Restorer with a nylon scuffing pad as per instructions on label.
• Be sure to rinse the wood well with clean water to remove surface dirt and allow it to dry thoroughly for three full days before applying Sikkens Cetol Marine products.

Application Procedure:

• Follow preparation procedures
• Apply one coat of Interlux Sikkens Cetol Marine Natural Teak Finish
• Wait 24 hours
• Apply second coat of Interlux Sikkens Cetol Marine Natural Teak Finish
• Wait 24 hours
• Apply third coat of Interlux Sikkens Cetol Marine Natural Teak Finish
• Always allow 24 hours drying time between coats. All coats should be applied within a 1-2 week period.

Application Tips:

It is not recommended to sand in between coats of Cetol on exterior wood. This will lower the overall layer thickness, which is very important for effective product performance. To achieve a non-skid surface, evenly sprinkle Interlux Intergrip 2398c Polymeric Non-Skid Compound onto the wet surface immediately after applying the second coat of Cetol. If needed, do the same after the third coat as well. The addition of Intergrip 2398c will reduce the life of the Cetol Marine Natural Teak.

If a high gloss finish is desired, Cetol Marine Gloss can be applied after the initial application of three coats of Cetol Marine. Sikkens Cetol Marine Gloss should never be applied on a deck as the surface will become dangerously slippery when wet.

Maintenance:

• Exterior:
• Before application of a maintenance coat of Cetol, clean the entire surface with Interlux All-Purpose Boat Soap to remove any surface contaminants as per instructions on label. If mildew is present, use Interlux Premium Teak Restorer with a nylon scuffing pad, as per instructions on label.
• Be sure to rinse the wood well with clean water to remove surface dirt and allow it to dry thoroughly. Sikkens Cetol Marine Gloss should be sanded to a dull finish using 220-320 grit sandpaper. Remove all dust before applying the maintenance coat of Cetol Marine.
• Interior:
• Apply a coat of Sikkens Cetol Marine as visually required. Before application of the maintenance coat, wash the surface with Interlux All-Purpose Boat Soap, as per label instructions, then sand the surface lightly with 220-320 grit sandpaper.
• Be sure to remove all sanding dust with a vacuum. Once clean, apply the maintenance coat.

Click to Download Sikkens Cetol Marine Natural Teak Finish Application Instructions

Frequently Asked Questions

What is Interlux Sikkens Cetol Marine Natural Teak Finish used for?

Interlux Sikkens Cetol Marine Natural Teak Finish is a satin, translucent wood finish for interior and exterior hardwoods above the waterline. It is designed for woods such as teak, mahogany, and oak while enhancing the natural wood grain and providing UV-absorbing protection through Sikkens Cetol Marine's Next Wave technology.

Can Sikkens Cetol Marine Natural Teak Finish be used below the waterline?

No. Sikkens Cetol Marine Natural Teak Finish is designed for interior and exterior wood applications above the waterline. The application instructions specifically state that the product should not be applied below the waterline.

How many coats of Sikkens Cetol Marine Natural Teak Finish should be applied?

Apply three coats for the initial application. Allow 24 hours of drying time between coats, and apply all three coats within a 1–2 week period. For exterior wood, sanding between coats is not recommended because it reduces the overall finish thickness.

How should Sikkens Cetol Marine Natural Teak Finish be applied?

Use a long-haired natural bristle brush and apply the finish in the direction of the wood grain. Apply liberal coats while maintaining a wet edge and saturating the end grains. The recommended application temperature is 50°F to 95°F.

How should wood be prepared before applying Sikkens Cetol Marine Natural Teak Finish?

For new wood, remove surface oils and contaminants with Interlux Special Thinner 216, then sand with 180–220 grit sandpaper along the grain and remove the sanding dust. Previously coated wood requires removal of existing coatings before following the new-wood preparation procedure. Weathered or previously oiled wood requires additional preparation with Interlux Premium Teak Restorer.

What is Next Wave technology in Sikkens Cetol Marine Natural Teak Finish?

Next Wave technology is a UV-absorbing formulation designed to help protect wood from the damaging effects of sunlight. The technology uses specialty resins and advanced UV absorbers to enhance color retention and help extend the longevity of the wood finish.

California Residents: WARNING Cancer and Reproductive Harm - P65Warnings.ca.gov